Top 350+ Solved Digital Electronics and Logic Design MCQ Questions Answer
Q. The implementation of simplified sum-of-products expressions may be easily implemented into actual logic circuits using all universal gates with little or no increase in circuit complexity. (Select the response for the blank space that will BEST make the statement true.)
a. and/or
b. nand
c. nor
d. or/and
Q. Which of the following statements accurately represents the two BEST methods of logic circuit simplification?
a. boolean algebra and karnaugh mapping
b. karnaugh mapping and circuit waveform analysis
c. actual circuit trial and error evaluation and waveform analysis
d. boolean algebra and actual circuit trial and error evaluation
Q. Which of the following combinations cannot be combined into K-map groups?
a. corners in the same row
b. corners in the same column
c. diagonal corners
d. overlappin g combinati ons
Q. As a technician you are confronted with a TTL circuit board containing dozens of IC chips. You have taken several readings at numerous IC chips, but the readings are inconclusive because of their erratic nature. Of the possible faults listed, select the one that most probably is causing the problem.
a. a defective ic chip that is drawing excessive current from the power supply
b. a solar bridge between the inputs on the first ic chip on the board
c. an open input on the first ic chip on the board
d. adefective output ic chip that has an internal open to v cc
Q. The device shown here is most likely a .
a. comparator
b. multiplexer
c. demultiplexe r
d. parity generator
Q. For the device shown here, assume the D input is LOW, both S inputs are HIGH, and the input is HIGH. What is the status of the outputs?
a. all are high.
b. all are low.
c. all but are low.
d. all but are high.
Q. In VHDL, macrofunctions is/are:
a. digital circuits.
b. analog circuits.
c. a set of bit vectors.
d. preprogra mmed ttldevices.
Q. Which of the following expressions is in the product-of-sums form?
a. (a + b )(c + d )
b. (ab )(cd )
c. ab (cd )
d. ab + cd
Q. Which of the following is an important feature of the sum-of-products form of expressions?
a. all logic circuits are reduced to nothing more than simple and and or operations.
b. the delay times are greatly reduced over other forms.
c. no signal must pass through more than two gates, not including inverters.
d. the maximum number of gates that any signal must pass through is reduced by a factor of two.
Q. An output gate is connected to four input gates; the circuit does not function. Preliminary tests with the DMM indicate that the power is applied; scope tests show that the primary input gate has a pulsing signal, while the interconnecting node has no signal. The four load gates are all on different ICs. Which instrument will best help isolate the problem?
a. current tracer
b. logic probe
c. oscilloscope
d. logic analyzer
Q. The binary numbers A = 1100 and B = 1001 are applied to the inputs of a comparator. What are the output levels?
a. a > b = 1, a < b= 0, a < b = 1
b. a > b = 0, a < b = 1, a = b = 0
c. a > b = 1, a < b = 0, a = b = 0
d. a > b = 0, a < b = 1, a = b = 1
Q. A logic probe is placed on the output of a gate and the display indicator is dim. A pulser is used on each of the input terminals, but the output indication does not change. What is wrong?
a. the output of the gate appears to be open.
b. the dim indication on the logic probe indicates that the supply voltage is probably low.
c. the dim indication is a result of a bad ground connection on the logic probe.
d. the gate may be a tristate device.
Q. Each "1" entry in a K-map square represents:
a. a high for each input truth table condition that produces a high output.
b. a highoutput on the truth table for all low input combination s.
c. a lowoutput for all possible high input conditions.
d. a don\t carecondition for all possible input truth table combinati ons.